Kodiak Hydraulic Brake Hose 48" 1/8" ID 3/16" Male Inverted Flare x Male Inverted Flare
DOT-approved flexible hydraulic brake hose for trailer brake systems. This 48" Kodiak hose uses 3/16" male inverted flare fittings on both ends and is designed to help maintain secure brake-fluid flow in hydraulic trailer brake applications.
Overview
Worn, cracked, kinked, or leaking brake hoses can reduce hydraulic pressure and weaken trailer stopping performance. The BH-3MFS-048 is a 48" flexible hydraulic brake hose built for trailer brake systems using compatible 3/16" brake line connections. It provides a male inverted flare fitting on both ends for a secure brake-line connection.
R&P Service Insight
Hydraulic brake hoses are small parts with a big job. A hose that is too short, kinked, twisted, cracked, or leaking can affect brake response and make routing difficult during installation.
- Pressure Matters: Leaks or restrictions can reduce hydraulic brake performance.
- Fitment Check: Verify 3/16" inverted flare compatibility before ordering.
- Routing Check: Confirm the 48" length allows smooth routing without pulling, rubbing, or kinking.
R&P Knowledge Hub
Compatibility: Designed for hydraulic trailer brake systems using compatible 3/16" brake line connections.
Vehicle / System Fit: Used with hydraulic trailer brake systems, commonly including hydraulic disc brake setups where the length, flare type, thread, and routing match.
Installation Notes: Swivel-style male ends help position the hose during installation without twisting the hose body. Verify flare type, thread, and connection style before installation.
Performance Insight: Flexible brake hose sections help bridge moving or hard-to-route areas while maintaining hydraulic brake-fluid flow.
Brand & Fitment Note
Selling Brand: Kodiak
Application Reference: This is a universal-style hydraulic brake hose for compatible trailer brake systems, not a vehicle-specific part.
What This Means: This listing is for a Kodiak flexible hydraulic brake hose where the buyer's trailer brake system matches the 48" length, 3/16" male inverted flare fittings, thread compatibility, and routing requirements.
Before Ordering: Verify hose length, flare type, thread, routing, brake-line size, and hydraulic system configuration before installation.
R&P Repair Insight
Brake hose replacement is often straightforward, but correct routing and fitting match are critical. A hose that is twisted, kinked, stretched, or connected to the wrong flare style can create leaks, pressure loss, or premature wear.
- Length Check: Confirm 48" is the correct routed length for your trailer.
- Connection Check: Verify 3/16" male inverted flare compatibility on both ends.
- Final Brake Check: After installation, bleed the brake system as needed and inspect for leaks before towing.
Features
DOT-Approved Hydraulic Brake Hose
Built for hydraulic trailer brake systems where a flexible brake hose is required between compatible brake-line components.
48" Flexible Routing Length
Provides a 4 ft flexible connection for routing around the trailer frame, axle, suspension, caliper area, actuator area, or other brake-line routing points.
3/16" Male Inverted Flare Ends
Male inverted flare fittings on both ends connect to compatible 3/16" hydraulic brake line systems.
Swivel-Style Male Ends
Swivel-style ends help position the hose during installation and reduce twisting of the hose body.
Flexible, Kink-Resistant Construction
Reinforced flexible hose helps route brake fluid through tight installation spaces while reducing the risk of flow-restricting kinks.
Corrosion-Resistant Brake-Line Hardware
Built for trailer service in wet, muddy, salty, and marine environments where brake components are exposed to harsh conditions.
Specifications
| Specification | Detail |
|---|---|
| Part Number | BH-3MFS-048 |
| Brand | Kodiak |
| Product Type | Flexible hydraulic trailer brake hose |
| Application | Hydraulic trailer brake systems |
| Hose Length | 48" / 4 ft |
| Inner Diameter | 1/8" ID |
| Fitting Type | 3/16" male inverted flare x 3/16" male inverted flare |
| Thread | Commonly used with 3/8"-24 inverted flare brake-line connections |
| Material | Rubber, brass, and stainless steel |
| Finish / Construction Note | Flexible rubber hose body with brake-line hardware intended for corrosion-resistant trailer service |
| Approval | DOT-approved brake hose |
| Alternate Reference | 034-BH-3MFS-048 |
Fitment / Application
| Category | Details |
|---|---|
| Vehicle / System | Hydraulic trailer brake systems |
| Primary Fit | Universal-style fit for compatible hydraulic trailer brake systems where the hose specifications match |
| Brake Type | Commonly used with hydraulic disc brake setups; may also be used where this fitting and length match the hydraulic trailer brake system |
| Line Compatibility | Compatible with standard 3/16" brake line systems using matching inverted flare connections |
| Common Use Areas | Trailer frame routing, axle-to-frame connections, caliper routing, actuator routing, swing-tongue areas, and multi-axle trailer brake line layouts |
| Notes | Verify length, flare type, thread, and routing before installation. Brake systems should be checked for leaks and properly bled after hose replacement. |
Included Components
| Quantity | Item |
|---|---|
| 1 | 48" hydraulic trailer brake hose with 3/16" male inverted flare fittings on both ends |
